How to Do Your Own Box Braids

If you're wondering how to do your own box braids, then you've come to the right place! This article will show you how to properly protect your hair and prepare it for the braiding process. Next, follow the steps listed below to gather and split your hair into two or three parts. After the prep phase, the actual braiding process can begin! After all, it's much easier to create a perfect box braid than you think!

Protection Prep Your Hair

There are several things to keep in mind when protecting your hair before doing box braids. The most obvious is to use a leave-in conditioner to keep it from becoming tangled or damaged during the braiding process. It's also important to use a conditioner spray, as wet hair is most fragile. Before taking down the braids, coat each section with conditioner. Gently take the braids out, working your way from the front to the back.

A protective style is exactly what it is, because the pressure of the braiding process can harm your hair and scalp. It can cause breakage, tangling, and even headaches if you pull too tightly. To avoid damaging your hair, you should not leave your protective style on for longer than two weeks. After the protective style has been removed, you should always moisturize and wash your hair. If you have long hair, do not try to undo the braids immediately.

Before doing box braids, wash your hair. Always wash your hair in a vertical motion, not at a horizontal angle, to prevent frizz. Also, apply a heat protectant to help keep the protective style from drying out your hair. A silk scarf can also be helpful when sleeping with a protective style. A silk pillowcase is also a great way to protect your hair from breakage during the night.

Part Hair Into Sections

For this easy-braid style, you need to part your hair into sections. Before braiding, use a gentle shampoo to clean your hair and condition it. Use a deep conditioner and heat protectant styling spray, and dry your hair gently in sections. Then, follow the directions in the following video to create your new box braids! After braiding, wash your hair again, and repeat the process if needed.

To begin, part your hair into sections. The smaller the sections, the larger the braids will be. Use a precision comb to make clean parts, or a hair band to secure each section. Once the sections are secured, begin braiding! Make sure to place the braids on the sectioned hair. You will need a comb to hold the hair in place, so it's important to use a comb that separates the hair in smaller sections.

Once the sectioning is done, place the braiding hair into the middle of the folded section. Repeat this process for all of the sections. To complete this style, you must have about half an inch of braiding hair. Start at the back and work your way out. You can use a rat tail comb to create box-shaped parts. After your hair is braided, secure the ends using rubber bands.

Gather and Split Your Braiding Hair

For this hairstyle, you will need to gather and split your hair into three equal sections. Begin by gathering the two sections near the nape of your neck. Hold one section with your right hand and the other with your left hand. Now, take the right strand and cross it over the center strand. Once you've completed this step, move onto the next section. Repeat these steps for the remaining hair.

Depending on the thickness and length of your hair, the box braid process can take anywhere from four to twelve hours. It's important to use a moisturizing shampoo, and deep conditioner, as well as a heat-protective styling spray. Once you're finished, dry your hair gently in sections. Don't forget to keep your braids moisturized by wearing a silk scarf. Here are some simple steps for gathering and splitting your own box braid hair.

To start your braid, section off your hair into three sections. The smaller the sections, the smaller your braids will be. Niani recommends using a precision comb or alligator clips to ensure the parts are clean and straight. To start your braid, cut a small piece near your hairline. Divide this small section into three equal sections, one on each side. Repeat for all three sections. This will create the center section.

Braid The Braiding Hair Into Your Hair

Start by sectioning the hair into three equal strands at the nape of your neck. Hold the right and left strands in your hands. Cross the right strand over the center strand. Move your right hand toward the left. Repeat with the other strand. Eventually, you should have three strands braided into your hair. Continue to repeat the steps until you have braided all three strands into one strand.

To create a basic braiding pattern, you should divide your hair into three sections. Start from the center part and cross the two remaining strands under the middle strand. Pick up the strand closest to your face. This piece will become your new center section. Continue to braid the remaining hair until the entire head is covered. Finish with an elastic to secure the braid. Once you're satisfied with the braid, add more strands and braid them.

The braiding process begins by sectioning the hair. Then, with a tail of the comb, separate each section. Start with the left or right side rather than the center. You can also clip some clips to help keep the braiding hair neat. Next, cut a small piece of hair close to your hairline. Separate these into three equal pieces. Repeat the process for each section. The braiding process is easy, and you'll be amazed at how beautiful your hair looks!

Repeat Until All Hair Sections Are Done

Once you've completed the first two steps of box braiding, you can go ahead and add the third step. Simply divide your hair into two equal sections and crisscross one of the smaller pieces underneath the larger one. Make sure to bend the bottom loop and keep it secure with a rubber band. Repeat until all sections are braided. Once you're finished, you'll want to repeat this process with the remaining hair sections.

To add hair to your braid, part a section of natural hair. Place two strands of yarn on either side of the center section. Twist the yarn once so that it doesn't slip while braiding. Separate each strand of yarn into three legs. Place one hair section behind the other to form a diagonal line. Continue adding hair to the braids until all of the hair sections are braided.

When you're done, secure the braids with clips and hair ties. You can also use a rubber band to secure the ends. Then, repeat the process of braiding until all sections are finished. Depending on the size of your hair, you may have to repeat this process a couple of times. Depending on the length of your hair, you may want to start with a smaller section if you have very short hair.